Many people enjoy relaxing in a warm cozy bath after a tiring day at work. As the tub begins to fill up, you could observe a strange thing happening the water is slow to drain away and does not rise above a certain amount. Sometimes, the issue may be due to a mistake in forgetting to change the drain stopper. In other situations, the bathtub won’t hold water because of more complex problems with the plumbing.
Your bathtub might be unable to hold water for one or many reasons. The most commonly cited reason is that you’ve got an issue with the plumbing system. No matter what the root cause, you must consult a local plumber to conduct a thorough examination. A professional plumber will determine why the drain in your bathtub is leaking and offer a feasible solution.
While it is difficult when the drain in your bathtub isn’t working, The issue is simple to solve. Finding out the root causes will allow you to make the needed repairs completed. There are six reasons why your bathtub won’t correctly hold water:
1: The Bathtub Drain Stopper Is Not Working
This bathtub drainage assembly could appear to be a bit cryptic. If your bathtub isn’t holding water, it could be a malfunctioning stopper drain. A lever above the bottom part of the tub determines to store the water in the tub when required. The tub also gets drained when it isn’t get used.
Most of the time, problems with the stopper for draining your bathtub are because it gets disconnected from the plug or spring connecting it with the linkage. The stopper’s connection gets broken to the lever that controls the trip, and the pin cannot keep water as it is supposed to. It’s helpful to know that replacing a broken bathtub drain stopper is easy. If your changes cannot resolve the issue, you may require an installation of a bathtub drain.
2: The Bathtub Cannot Hold Water Because Is Clogged
Even if there’s a stopper for the bathtub drain installed, the water may not be able to stay in the tub long or at all enough to permit one to end bathing. Old pipes are prone to collecting grease and hair. The water gets then forced to search for other routes for escape.
In some instances, there may be a blockage that will not dissolve. There may be more resistance, such as caps for shampoo bottles or razor covers leaking down the drain. The stopper for the bathtub’s drain could also be blocked. To avoid clogs check the plug regularly and then have a plumber in the area resolve any issues that arise.
3: There Is a Risk of a Catastrophic Overflow of Tubes in the Bathtub
In some cases, an overflow drainage assembly likely is to blame for your tub’s lack of water storage capacity. This part is a safety feature that lets water that gets overfilled back into the drainpipes to prevent it from spilling onto the edge of the tub. If the fittings of the tub are not tight and water leaks into the tub, and may damage the floor beneath the tub.
If you regularly bathe with more water and the overflow tube tends to leak, it could be the reason for the issue. Ensure the overflow tube is tightened or buy a replacement gasket to remedy the problem.
4: There Is a Faulty Connection to the Bathtub
Another possible issue could be the linkage responsible for moving the drain stopper upwards and down. Be sure to check that the link is properly connected and operating correctly. It is done by pulling on the lever, then lifting it to reveal the connection. If the plug and the spring get not connected to the linkage, you can use a magnetic tool to secure it.
The linkage could also become bent or tangled. Verify that it’s lying straight and straight and that the pin on top is in position. If the U-shaped pin is broken or missing, replace it. After everything gets set, adjust the linkage’s length to ensure it’s functioning as it should.
5: The Bathtub Doesn’t Hold Water Due to Corrosion or Rust
As time passes, pipes become rusty. They cannot support fluid flow and become affected both outside and within. Rusted and corrosion-prone pipes could cause leaks in the system, resulting in an alternative route for the water intended for your tub.
Different factors can cause the degradation of pipes due to a variety of factors. For instance, the pH level can affect the speed at which your drains and pipes are corroding. The water with a pH lower than seven get considered to be acidic. Low pH water has higher dissolved solids, including lead, copper, and calcium. When acidic water flows through your pipes made of metal, it absorbs minerals and substances from the pipes’ walls, making them thinner.
6: Temperature Changes Caused Problems Connecting Water to Your Bathtub
The temperature fluctuations could cause pipes to expand and contract. It is because they get mostly made of iron. The seals and connections loosen in the process and provide a different way for water to flow through. Suppose the temperature has impacted the pipes connecting to the bathtub. In that case, the water may flow out instead of settling inside the tub.
You can rely on the helpful experts from Ottawa Plumbing Service for any plumbing issues you may be experiencing. Whether a simple or complicated emergency repair or installing new showers and bathtubs. Call our trusted Ottawa plumbers at (613) 317-1682 or email us at info@ottawaplumbingservice.com.
